Detailed overview of measurement quantities, ranges and measurement capabilities are available via Accreditation for reverification of measurement instruments covered by the Executive orders of the Danish Safety Technology Authority on the use of measurement instruments subject to legal metrology.
View accreditation certificate
Caliper 0-1000mm
Internal Micrometer 4-225mm
External Micrometer 0-1000mm
Ring 0-250mm
Threat plug 0-200mm
Height gauges 0-1000mm
Dial gauges 0-200mm
Measuring pins 0,-35mm
Feeler gauges 0-2mm
Setting standard 0-600mm
Profil projector 0-300mm
AC-DC voltage difference
(10 Hz – 1 MHz )
AC-DC current difference
(10 Hz – 100 kHz )
Voltage (DC) 1V – 40kV
Voltage (AC)
(50 Hz – 60 Hz ) 1kV -28kV
Voltage (AC)
(10 Hz – 500 Hz ) 1kV – 6kV
Voltage (AC)
(500 Hz – 1 kHz ) 1kV – 6kV
Voltage (AC)
(DC – 1 MHz ) 0,1kV – 20kV
Resistance 0 -100T
Current (DC) 0A – 2000A
Voltage (AC)
Current (AC)
Power (DC and AC) 1mW – 1MW
Energy 1mJ – 10GJ
Capacitance
(20 Hz – 100 kHz ) 10 fF 10 μF
Q-factor
(50 Hz – 10 kHz ) 0 1000
Dissipation coefficient
(20 Hz – 100 kHz ) 0,01 4
Inductance
(100 Hz – 10 kHz ) 1 μH 10H
Distorsion
(10 Hz – 100 MHz )
Sinad
(20 Hz – 100 kHz ) -99,99 dB 0 dB
Signal to noise ratio
(50 Hz – 100 kHz ) -99,99 dB 0 dB
Rise/falltime
(Risetime ) 0,35 ns 1,5 ns
Current (AC)
(Peakcurrent ) 2,5 A 50 A
Current (AC)
(Current, 30 ns ) 1 A 25 A
Current (AC)
(Current, 60 ns ) 0,5 A 15 A
Power (HF)
(1 kHz – 26,5 GHz ) 1nW – 500W
Calibration factor
(1 kHz – 26,5 GHz )
Reflectance coefficient (HF)
(100 kHz – 18 GHz )
Reflectance coefficient (HF)
(Modulus, 1 kHz – 26,5 GHz )
Reflectance coefficient (HF)
(Fase, 1 kHz – 26,5 GHz )
Directivity
(100 kHz – 26,5 GHz )
Attenuation
(100 kHz – 18GHz )
Transmission coefficient (HF)
(Modulus, 1 kHz – 26,5 GHz )
Transmission coefficient (HF)
(Fase, 1 kHz – 26,5 GHz )
Modulation (AM)
(10 Hz – 300 kHz )
Modulation (FM)
(10 Hz – 300 kHz ) 25 Hz 700 kHz
From 10 ml/min to 10 l/min air or nitrgen with Fluke flowmeters.
Relative humidity of air
(-5°C – 90°C ) Over water. Below 5°C humidity cannot be controlled but only measured.
Relative humidity of air
(-30°C – 0°C ) Over ice. Humidity cannot be controlled but only measured.
Temperature (air)
(Dug punkt ) Frost point. Over ice.
Relative humidity of air
(-30°C – 0°C )Dew point. Over water.
Calibration of scales for static weighing. 1mg -35000kg
Load 1mg-64kg
IR equipments -30-400C
Temperature Gauges -80C- 650C
Frequency 10 μHz 40GHz
Timeinterval 1 ns 1000 s
Period 25 ps 100Ks
Rise/falltime 15 ps 1 ns
Phase
(1 kHz – 100 kHz )
Phase
(0,1 Hz – 1 kHz )
Phase
(100 kHz – 10 MHz )
Rotationel frequency 0 rpm 100000 rpm
Verification of non-automatic scales cf. EN45501. Verification of automatic scales with a national type approval. 1mg-160000kg
Verification of weighing conveyor calibrated cf. OIML R51. 200kg-200000kg
Verification of automatic scales approved cf. OIML R51 for weighing of pre-packed articles. 100mg-2000kg
Global Calibration Scope
Common equipment serviced: Conductivity meters, Salinity meters, pH meters, Sucrose solutions, Gas detectors and gas concentration, Particle counters, Refractometry instruments, Viscosity instruments
This site holds the competency for the specified domain. If your requirement is outside the scope of competency, we may be able to transfer the instrument with your permission to another Trescal laboratory that holds the applicable scope. Please refer to the scope of accreditation for accredited capabilities specific to this laboratory.
Global Calibration Scope
Common equipment serviced: Dynamometers, Force machines (Tension and/or Compression), Load cell, Force gauges, Strainmeter, Crimping pliers, Charpy testers, Cable tie tools, Press, Retention tools, Wire wrap tools, Spring balance
This site holds the competency for the specified domain. If your requirement is outside the scope of competency, we may be able to transfer the instrument with your permission to another Trescal laboratory that holds the applicable scope. Please refer to the scope of accreditation for accredited capabilities specific to this laboratory.
Global Calibration Scope
Common equipment serviced: Illuminance meter, Luminance meter, Spectrophotometer, Glossmeter, Photometer, Colorimeter, Pyranometer, Irradiance meter
This site holds the competency for the specified domain. If your requirement is outside the scope of competency, we may be able to transfer the instrument with your permission to another Trescal laboratory that holds the applicable scope. Please refer to the scope of accreditation for accredited capabilities specific to this laboratory.
Global Calibration Scope
Common equipment serviced: Burettes, Flask, Syringe, Pipettes, Test tubes, Beakers, Dispenser, Tanks, Vessels, Gauge overflow, Gauge windows, Concrete air content meters, Level probes Pycnometers, Titrators
This site holds the competency for the specified domain. If your requirement is outside the scope of competency, we may be able to transfer the instrument with your permission to another Trescal laboratory that holds the applicable scope. Please refer to the scope of accreditation for accredited capabilities specific to this laboratory.
Caliper 0-1000mm
Internal Micrometer 4-225mm
External Micrometer 0-1000mm
Ring 0-250mm
Threat plug 0-200mm
Height gauges 0-1000mm
Dial gauges 0-200mm
Measuring pins 0,-35mm
Feeler gauges 0-2mm
Setting standard 0-600mm
Profil projector 0-300mm
AC-DC voltage difference
(10 Hz – 1 MHz )
AC-DC current difference
(10 Hz – 100 kHz )
Voltage (DC) 1V – 40kV
Voltage (AC)
(50 Hz – 60 Hz ) 1kV -28kV
Voltage (AC)
(10 Hz – 500 Hz ) 1kV – 6kV
Voltage (AC)
(500 Hz – 1 kHz ) 1kV – 6kV
Voltage (AC)
(DC – 1 MHz ) 0,1kV – 20kV
Resistance 0 -100T
Current (DC) 0A – 2000A
Voltage (AC)
Current (AC)
Power (DC and AC) 1mW – 1MW
Energy 1mJ – 10GJ
Capacitance
(20 Hz – 100 kHz ) 10 fF 10 μF
Q-factor
(50 Hz – 10 kHz ) 0 1000
Dissipation coefficient
(20 Hz – 100 kHz ) 0,01 4
Inductance
(100 Hz – 10 kHz ) 1 μH 10H
Distorsion
(10 Hz – 100 MHz )
Sinad
(20 Hz – 100 kHz ) -99,99 dB 0 dB
Signal to noise ratio
(50 Hz – 100 kHz ) -99,99 dB 0 dB
Rise/falltime
(Risetime ) 0,35 ns 1,5 ns
Current (AC)
(Peakcurrent ) 2,5 A 50 A
Current (AC)
(Current, 30 ns ) 1 A 25 A
Current (AC)
(Current, 60 ns ) 0,5 A 15 A
Power (HF)
(1 kHz – 26,5 GHz ) 1nW – 500W
Calibration factor
(1 kHz – 26,5 GHz )
Reflectance coefficient (HF)
(100 kHz – 18 GHz )
Reflectance coefficient (HF)
(Modulus, 1 kHz – 26,5 GHz )
Reflectance coefficient (HF)
(Fase, 1 kHz – 26,5 GHz )
Directivity
(100 kHz – 26,5 GHz )
Attenuation
(100 kHz – 18GHz )
Transmission coefficient (HF)
(Modulus, 1 kHz – 26,5 GHz )
Transmission coefficient (HF)
(Fase, 1 kHz – 26,5 GHz )
Modulation (AM)
(10 Hz – 300 kHz )
Modulation (FM)
(10 Hz – 300 kHz ) 25 Hz 700 kHz
From 10 ml/min to 10 l/min air or nitrgen with Fluke flowmeters.
Relative humidity of air
(-5°C – 90°C ) Over water. Below 5°C humidity cannot be controlled but only measured.
Relative humidity of air
(-30°C – 0°C ) Over ice. Humidity cannot be controlled but only measured.
Temperature (air)
(Dug punkt ) Frost point. Over ice.
Relative humidity of air
(-30°C – 0°C )Dew point. Over water.
Calibration of scales for static weighing. 1mg -35000kg
Load 1mg-64kg
IR equipments -30-400C
Temperature Gauges -80C- 650C
Frequency 10 μHz 40GHz
Timeinterval 1 ns 1000 s
Period 25 ps 100Ks
Rise/falltime 15 ps 1 ns
Phase
(1 kHz – 100 kHz )
Phase
(0,1 Hz – 1 kHz )
Phase
(100 kHz – 10 MHz )
Rotationel frequency 0 rpm 100000 rpm
Verification of non-automatic scales cf. EN45501. Verification of automatic scales with a national type approval. 1mg-160000kg
Verification of weighing conveyor calibrated cf. OIML R51. 200kg-200000kg
Verification of automatic scales approved cf. OIML R51 for weighing of pre-packed articles. 100mg-2000kg